Altering the water filter in your Kenmore fridge is a straightforward job that may be accomplished in only a few minutes. By following these straightforward steps, you’ll be able to be sure that your fridge is allotting clear, recent water for your loved ones to take pleasure in.
Start by finding the water filter housing. That is sometimes discovered within the higher right-hand nook of the recent meals compartment. Upon getting situated the housing, press the discharge button and pull the housing straight in direction of you. It will expose the outdated water filter. Grip the outdated filter firmly and switch it counterclockwise to take away it from the housing.
Subsequent, take the brand new water filter and align it with the housing. Push the filter into the housing and switch it clockwise till it’s comfortable. As soon as the filter is in place, push the housing again into the fridge and press the discharge button to lock it into place. Reset the water filter indicator mild by urgent and holding the sunshine for five seconds. Your fridge will now dispense clear, recent water for you and your loved ones to take pleasure in.
Establish the Mannequin and Find the Filter
Earlier than you begin the method of adjusting the water filter in your Kenmore fridge, it is essential to establish your particular mannequin. The situation and accessibility of the water filter can fluctuate relying on the fridge mannequin. This is a step-by-step information that can assist you establish your mannequin and find the filter:
Mannequin Identification:
Find the mannequin quantity label in your fridge. It is normally discovered on the within of the fridge (behind the crisper drawers or on the aspect wall) or on the again of the fridge. The mannequin quantity consists of a mix of letters and numbers, sometimes beginning with the prefix “795” or “106.” Notice down the mannequin quantity for reference.
Filter Location:
Upon getting recognized your fridge mannequin, seek the advice of your consumer handbook or test on-line assets to find out the situation of the water filter. In most Kenmore fridges, the filter could be present in one of many following areas:
- Contained in the fridge compartment: Search for a small door or panel on the ceiling, aspect wall, or again wall of the fridge part.
- Behind the bottom grille: Take away the decrease grille on the backside of the fridge to entry the filter.
- Within the dispenser drawer: Pull out the dispenser drawer and test for a filter situated throughout the drawer.
In some circumstances, the water filter could also be situated behind the kickplate on the backside of the fridge. To take away the kickplate, use a screwdriver or pry bar to softly elevate it off.
| Mannequin | Filter Location |
|---|---|
| 795.77999800 | Contained in the fridge compartment, on the ceiling |
| 106.51102700 | Behind the bottom grille |
Step 3: Take away the Previous Water Filter
Vital: Earlier than eradicating the outdated water filter, ensure to have a towel or bowl useful to catch any water which will leak out.
Disconnect the Water Line
Find the water line related to the outdated water filter. It’s sometimes a skinny, plastic tube. Gently squeeze the discharge clips on each ends of the water line and pull the road away from the filter housing.
Unthread the Previous Filter
Grasp the outdated water filter and switch it counterclockwise to loosen it. As soon as it’s unfastened, pull it straight out of the filter housing. Water could drip out as you take away the filter, so you’ll want to have a towel or bowl beneath to catch it.
Clear the Filter Housing
As soon as the outdated filter is eliminated, take a second to wash the within of the filter housing. Use a clear fabric or sponge to wipe away any particles or sediment which will have collected. It will be sure that the brand new filter suits snugly and operates correctly.
Collect Obligatory Supplies |
|---|
| Substitute water filter |
| Wrench (non-obligatory) |
| Towel or bowl |
| Security glasses (beneficial) |
Flip Off the Water Provide
Earlier than starting the method of adjusting the water filter in your Kenmore fridge, it’s essential to show off the water provide. This step is important to stop any water leakage through the filter substitute course of. This is how you are able to do it:
- Find the water provide valve: The valve is normally discovered behind the fridge or beneath the sink. It’s sometimes a small, blue or purple lever.
- Shut the valve: Flip the lever clockwise to shut the valve. It will cease the move of water to the fridge.
- Verify for leaks: Open the fridge door and press the water dispenser button to launch any remaining water stress. If there are not any leaks, you’ve gotten efficiently turned off the water provide.
Substitute the Previous Filter with a New One
1. Twist Out the Water Filter Cap
Find the small cap that covers the water filter. Sometimes positioned on the high of the fridge’s inside, underneath the water dispenser. Firmly grasp the cap and twist it counterclockwise to loosen and take away it.
2. Pull Out the Previous Filter
Attain into the compartment the place the water filter sits and gently pull the outdated filter straight out. Deal with it rigorously, as it might include residual water.
3. Insert the New Filter
Take the brand new water filter and line up its arrow or notch with the corresponding mark within the filter compartment. Slide the brand new filter into place till it suits snugly.
4. Twist On the Filter Cap
Retrieve the filter cap you eliminated earlier. Align it with the threads on the filter compartment and twist it clockwise to tighten it securely. Make sure the cap is correctly sealed to stop leaks.
5. Reset the Water Filter Standing
Most Kenmore fridges have a water filter standing indicator. To reset it after altering the filter, press and maintain the “Reset” or “Substitute” button on the management panel for a number of seconds (normally 5-10 seconds) till the indicator mild turns inexperienced or the show signifies that the filter has been changed. Seek the advice of your fridge’s consumer handbook for particular directions on resetting the filter standing.
Troubleshooting:
For those who encounter any points through the filter substitute course of, check with the next troubleshooting suggestions:
| Difficulty | Attainable Trigger | Resolution |
|---|---|---|
| Water Filter Cap Will not Flip | Tightly secured | Apply extra power whereas twisting |
| Water Leaking from the Filter Compartment | Free filter or cap seal | Make sure the filter is absolutely inserted and the cap is correctly tightened |
| Water Dispenser Not Dishing out Water | Reset Filter Standing indicator was not reset | Press and maintain the “Reset” or “Substitute” button on the management panel |
Reinstall the Filter Housing
After cleansing the filter housing, it is time to put the brand new filter again in and safe the housing. Observe these steps to reinstall the filter housing:
- Take the brand new water filter and align it with the housing. Make sure that the filter is inserted accurately, as indicated by the arrows or guides on the housing.
- Twist the filter into place by turning it clockwise. Tighten it snugly, however keep away from over-tightening, as this might harm the housing or filter.
- Find the filter housing cap and align it with the housing. Be sure that the cap is correctly seated and suits snugly.
- Screw the filter housing cap into place by turning it clockwise. Once more, tighten it securely however keep away from over-tightening.
- Open the chilly water faucet once more to flush out any air or particles from the system. Run the water for a couple of minutes, or till it runs clear.
- Reset the filter indicator mild in your fridge if relevant. This normally includes urgent a button or holding down a mix of buttons for just a few seconds, as laid out in your fridge’s consumer handbook.
| Filter Kind | Reset Gentle Technique |
|---|---|
| Screw-in Filter | Press and maintain the “Filter Reset” button for five seconds |
| Push-in Filter | Press and maintain the “Water Filter” button for 3 seconds |
Flip the Water Provide Again On
As soon as the brand new filter is in place, it is time to flip the water provide again on. Listed here are the steps:
Step 1: Find the Water Valve
Discover the water valve that provides water to the fridge. It is normally situated on the again or aspect of the fridge, close to the underside. The valve can have a deal with or knob.
Step 2: Flip the Valve Slowly
Flip the valve deal with slowly clockwise to open it. Flip it solely till it is comfortable, do not overtighten.
Step 3: Verify for Leaks
Examine the water connections and filter housing for any leaks. For those who discover any leaks, flip the valve off and tighten the connections or exchange the filter.
Step 4: Flush the Line
Dispense just a few cups of water from the dispenser to flush any air or particles from the water line. The water could also be discolored initially.
Step 5: Reset the Filter Indicator (Non-compulsory)
Some Kenmore fridges have a filter indicator mild that must be reset after altering the filter. Check with your fridge’s consumer handbook for particular directions on resetting the indicator.
Step 6: Get pleasure from Contemporary Filtered Water
Your Kenmore fridge’s water filter is now modified and able to give you clear, filtered water. The filter must be changed each 6 months or as beneficial by the producer.
Step 1: Collect Your Supplies
Earlier than you begin, collect the next supplies: a brand new water filter, a flashlight (non-obligatory), a screwdriver (non-obligatory), and a bucket or bowl.
Step 2: Find the Water Filter Housing
The water filter housing is normally situated contained in the fridge, behind the underside grill. Search for a small, spherical or sq. panel with a deal with or knob.
Step 3: Take away the Previous Water Filter
Press the button or flip the knob to launch the water filter housing. Seize the outdated filter and gently pull it straight right down to take away it.
Step 4: Take away the Previous O-rings (Non-compulsory)
If the outdated filter has two O-rings, take away them and examine them for harm. Substitute them if vital.
Step 5: Insert the New O-rings (Non-compulsory)
For those who eliminated the outdated O-rings, apply a small quantity of food-grade lubricant to the brand new ones and push them onto the brand new filter.
Step 6: Insert the New Water Filter
Maintain the brand new filter straight and insert it into the housing. Push it up till it clicks into place.
Step 7: Substitute the Water Filter Housing
Push the water filter housing again into place. Make sure that it snaps into place securely.
Step 8: Run Water By means of the Filter
Run water from the dispenser for a number of minutes to take away any air bubbles and flush out the system.
Step 9: Reset the Filter Indicator (if relevant)
Relying in your Kenmore fridge mannequin, you might must reset the filter indicator. To do that:
– Maintain down the “Water Filter” button on the management panel for 3-5 seconds.
– Press the “Up” or “Down” arrow on the management panel to pick “Reset Filter”.
– Press the “Choose” button to substantiate the reset.
Troubleshooting Frequent Points
1. Water Dispense Button Not Working
Make sure the water dispenser is unlocked. Press the “Unlock” button if relevant.
Verify if the water tank or filtration system is empty. Refill or exchange if vital.
Examine for any obstructions or kinks within the water traces.
2. Ice Maker Not Making Ice
Verify the ice maker is turned on and the freezer temperature is under 0 levels Fahrenheit.
Make sure that the water provide line is related and freed from ice or leaks.
Verify if the ice bin is full or frozen. Clear any blockages.
3. Water Tastes or Smells Dangerous
Substitute the water filter frequently (each 6 to 12 months).
Flush the water dispenser for 2-3 minutes to take away air or impurities.
Think about using a water pitcher with a built-in filter for added filtration.
4. Water Leaks from Dispenser
Examine the water traces for any cracks or tears. Tighten or exchange as wanted.
Verify if the water filter is correctly put in.
Make sure the drip tray is correctly positioned to gather extra water.
5. Water Leaks from Fridge
Make sure that the fridge door is absolutely closed and never obstructed by meals gadgets.
Examine the door gasket for any tears or gaps. Substitute or seal as vital.
Verify for any ice buildup on the evaporator coils.
6. Error Message “Change Filter” or “Substitute Filter”
Substitute the water filter with a brand new one.
Reset the filter standing indicator by urgent and holding the “Filter Reset” button.
7. Water Dispenser Not Dishing out Water
Make sure the water provide is turned on.
Examine the water traces for any kinks or blockages.
Make sure that the water dispenser is related to the water filtration system.
8. Ice Maker Not Dishing out Ice
Verify if the ice maker is turned on and the freezer temperature is under 0 levels Fahrenheit.
Make sure that the ice bin is just not too full.
Examine the ice maker for any blockages or harm.
9. Water Freezer Style or Smells Dangerous
Substitute the water filter frequently (each 6 to 12 months).
Clear the ice maker with a light bleach resolution and rinse totally.
Think about using a freezer-safe container to retailer ice to stop odors.
10. Error Message “Water Filter Bypassed”
Examine the water filter housing for any leaks or harm.
Verify if the water filter bypass valve is open. Flip it to the closed place if vital.
Verify the water filter is appropriate with the fridge mannequin.
The best way to Change Water Filter in Kenmore Fridge
Altering the water filter in your Kenmore fridge is a fast and straightforward job that may enhance the style and high quality of your water and ice. This is a step-by-step information on do it:
- Find the water filter: The water filter is normally situated contained in the fridge, both behind the highest grille or within the bottom-left nook.
- Flip off the water provide: Discover the water provide valve behind the fridge and switch it off.
- Take away the outdated filter: Find the plastic cap on the water filter and twist it counterclockwise to take away it. Pull the outdated filter straight right down to detach it.
- Insert the brand new filter: Take away the plastic cap from the brand new filter and insert it into the housing. Push it up firmly till it clicks into place.
- Tighten the plastic cap: Screw the cap clockwise till it is hand-tight.
- Activate the water provide: Return to the water provide valve and switch it on. Verify for leaks on the filter and connections.
- Run water by means of the dispenser: Press the water dispenser button for a number of minutes to flush out any air or impurities.
Individuals Additionally Ask
How typically ought to I modify the water filter in my Kenmore fridge?
Each 6 months or when the fridge indicator mild activates.
What kinds of water filters are appropriate with Kenmore fridges?
Kenmore fridges use their very own proprietary water filters. Verify the producer’s web site or seek the advice of your consumer handbook for the particular filter mannequin.
How do I do know if my water filter is clogged?
Indicators of a clogged water filter embody sluggish water move, cloudy or discolored water, or a lower in ice manufacturing.
Can I clear a clogged water filter?
No. Water filters usually are not designed to be cleaned and must be changed when clogged.
The place can I buy Kenmore water filters?
Kenmore water filters could be bought at Sears shops, on-line retailers reminiscent of Amazon, or equipment elements sellers.
